wu qi
Full Professor
Shanghai Institute of Special Equipment Inspection & Technical Research

Xu Haixiang
Associate Professor
Shanghai Institute of Special Equipment Inspection & Technical Research

Tang xiaoying
Shanghai Institute of Special Equipment Inspection & Technical Research

Liu Enpin
Associate Professor
Shanghai Institute of Special Equipment Inspection & Technical Research

Amplitude inspection of the large crawler crane without the marker of turning center



According to the inspection requirement of monitoring and management system for large lifting machinery in the national safety technical specification, safety monitoring and management system should be installed for crawler crane with a capacity of more than 100 tons. There is an inspection requirement for the amplitude accuracy of the crawler crane. It requires that the sensors should be tested accurately during operation and within the allowable range of the operation instructions. However, it is difficult to find the turning center of the crane without the marker of turning center on the spot. The revolving center is covered by the end cover, etc. because the crawler crane has been installed. Therefore, it is necessary to consider other ways to test the relevant parameters. In this paper the method is to make the best of the technical and precision advantages of the total station, and

Host city and venue

Vienna (Wien) is the federal capital and largest city of Austria, and one of the nine states of Austria. Vienna is Austria's primate city, with a population of about 1.9 million (2.6 million within the metropolitan area, nearly one third of Austria's population), and its cultural, economic, and political centre. It is the 7th-largest city by population within city limits in the European Union.  Read more...

Latest news

More information about final program and schedule during MHCL 2019 conference can be found ...
More in2019  

Agenda

MHCL 2019 conference Day 1


Wednesday - September 18th, 2019

  • 13.00 – 14.00 Registration of participants and welcome reception
    in front of lecture hall GM 2 Radinger, 1st floor
  • 14.00 – 14.15 Opening Session
    lecture hall GM 2 Radinger, 1st floor
  • 14.15 – 15.35 Plenary Session I, 2 invited lectures
    lecture hall GM 2 Radinger, 1st floor
  • 15.35 – 16.00 Coffee break
    GM 8/9 Motorensymposium, 2nd floor
  • 16.00 – 18.00 Plenary Session II, 3 invited lectures
    lecture hall GM 2 Radinger, 1st floor
  • 18.00 – 20.00 Welcome party
    GM 8/9 Motorensymposium, 2nd floor

MHCL 2019 conference Day 2

Thursday - September 19th, 2019
  • 08.50 – 09.20 Late registration
    in front of lecture hall GM 2 Radinger, 1st floor
  • 09.20 – 10.30 Session A1, 4 papers
    lecture hall GM 2 Radinger, 1st floor
  • 10.30 – 11.00 Coffee break
    GM 8/9 Motorensymposium, 2nd floor
  • 11.00 – 13.00 Session B1 – Parallel Session, 7 papers
    lecture hall GM 4 Knoller, 2nd floor
  • 11.00 – 13.00 Session C1 – Parallel Session, 7 papers
    lecture hall GM 2 Radinger, 1st floor
  • 13.00 – 14.00 Lunch
    GM 8/9 Motorensymposium, 2nd floor
  • 14.00 – 16.00 Session B2 – Parallel Session, 7 papers
    lecture hall GM 2 Radinger, 1st floor
  • 14.00 – 16.00 Session C2 – Parallel Session, 7 papers
    lecture hall GM 4 Knoller, 2nd floor
  • 16.00 – 16.30 Coffee break
    GM 8/9 Motorensymposium, 2nd floor
  • 16.30 – 18.00 Session C3, 5 papers
    lecture hall GM 2 Radinger, 1st floor
  • 19.45 – 22.00 Dinner, restaurant “Augustinerkeller“

MHCL 2019 conference Day 3


Friday - September 20th, 2019
  • 09.20 – 10.50 Session A2, 5 papers
    lecture hall GM 2 Radinger, 1st floor
  • 10.50 – 11.20 Coffee break
    GM 8/9 Motorensymposium, 2nd floor
  • 11.20 – 13.00 Session A3, 6 papers
    lecture hall GM 2 Radinger, 1st floor
  • 13.00 – 14.00 Lunch
    GM 8/9 Motorensymposium, 2nd floor
  • 14.00 – 15.00 Guided laboratory tours
  • 15.00 – 15.30 Closing Session
    lecture hall GM 2 Radinger, 1st floor